Hempcrete, also called hemp-lime, is a bio-composite made from hemp shiv — the woody inner core of the hemp stalk — bound with a lime-based binder and water. Once cast, it dries into a lightweight, highly insulating and moisture-regulating infill material. Published laboratory data on novel hemp-lime mixes show thermal conductivity values between 0.087 and 0.10 W/m·K, compressive strengths from 0.09 to 0.57 MPa, and specific heat capacities of 1250 to 1557 J/kg·K, depending on binder ratio and density. For specifiers comparing it against conventional insulation materials, these figures place hempcrete in the low-density, low-lambda-value category — not a structural material, but a genuine thermal and hygric infill.
What is hempcrete made of?
The basic recipe combines three components: hemp shiv, a lime binder, and water. Builders coat the shiv particles with the binder-water slurry, then cast or pack the mix before it hardens. While clay can also serve as a binder, lime is generally preferred because it resists moisture, mould and decay better than clay-bound mixes — which is why the material is widely known in Europe as hemp-lime. One study on recycled-pozzolan binder blends found that mixes with a 1:1 binder-to-hemp ratio and a density of 300–400 kg/m³ delivered the best balance of hygrothermal and mechanical performance for insulating infill wall applications in that research.
Mechanical and thermal properties at a glance
- Compressive strength: 0.09 to 0.57 MPa, depending on density and curing age
- Thermal conductivity: 0.087 to 0.10 W/m·K
- Specific heat capacity: 1250 to 1557 J/kg·K
- Average moisture buffer value: 2.78 g/m²·RH%, described as excellent moisture buffering capacity
- Optimal mix found in research: 1:1 binder-to-hemp ratio at 300–400 kg/m³ density
Researchers also tested a binder blend containing 10% recycled crushed brick as a pozzolan. Among the variants studied, this mix produced the lowest thermal conductivity, which the authors attribute to the recycled material's effect on the binder's pore structure. For a sustainable building material that already relies on a renewable crop, substituting part of the lime binder with recycled aggregate is a further step toward lowering embodied energy.
How is hempcrete applied on site?
There are two principal application routes. Cast-in-place hempcrete uses temporary formwork or permeable permanent sheathing around a timber or stud frame to form monolithic infill walls. Fresh out of the mixer, the material looks like crumbly, cohesion-free oatmeal; it only becomes workable once tamped and pressed into the formwork. Crews typically build up the wall in layers of four to eight inches (roughly 10–20 cm) before lifting and repositioning the slip forms for the next lift.
The second route uses precast hempcrete bricks, blocks or complete wall panels, produced off-site under controlled curing conditions. This removes on-site mixing and placing entirely but introduces mortar joints or overlap connections between units — and these joints create thermal bridging that can reduce the overall insulating performance compared with a monolithic cast wall. Anyone weighing precast against cast-in-place should treat this trade-off as a design decision, not a detail to be resolved later.
Drying time: what to plan for
Drying time after casting depends mainly on the moisture content of the fresh mix. As a planning rule, cast hempcrete walls generally need two to eight weeks to dry sufficiently — sometimes longer, depending on wall thickness, ambient humidity and ventilation on site. Only once the wall has fully dried can it carry a finish plaster layer directly, functioning as both insulation and plaster substrate in a single build-up, similar in principle to a light straw-clay system.
Where does hempcrete fit in the building envelope?
Hempcrete is not a load-bearing material; it is an infill and insulation layer applied around a structural frame, in floors, ceilings, roofs or window reveals. Its combination of low thermal conductivity and strong moisture buffering makes it relevant for building envelopes where indoor humidity regulation matters as much as the U-value — a profile that overlaps with the performance targets discussed for the insulation strategies used in passive-house construction. Compared with mineral or polymer insulation, hempcrete's low compressive strength and multi-week drying period mean it suits infill rather than structural roles, and project schedules need to account for that drying window before plastering or handover.
Practical take-away
- Check binder-to-hemp ratio and target density (300–400 kg/m³ performed best in published lab testing) before specifying a mix.
- Build up cast walls in 10–20 cm lifts; don't rush the tamping — the fresh mix has no cohesion until pressed.
- Budget two to eight weeks of drying time before applying finish plaster, longer in humid or poorly ventilated conditions.
- If using precast blocks or panels, factor in the thermal-bridging penalty at mortar joints when calculating envelope performance.


